![]() Note: If you don't know the password to your router's admin interface, you may want to lookup the defaults in its manual, sometimes on a sticker on the router itself, or in our hardware database of over 4000 routers. Login to your gateway's admin interface, usually by typing its IP address in your web browser, and find the DHCP range: You need to find the range of IPs used for DHCP so you can later set your access point to use an IP address outside that range (but on the same subnet). What that means is, the router acts as a DHCP server, and serves IP addresses dynamically, as needed to the client computers. Step 2: Connect to your router administration interface to find the DHCP rangeīy default, LAN clients are usually set to obtain their IPs automatically. It is usually in the .x range.Īlternaticely, you can try connecting to your router's default IP address by looking it up in our routers database. The " IP address" line in the above figure shows your computer's IP, while the "Default Gateway" is your main existing router that provides your internet connection. In this example, my ISP-provided gateway/router (the "Default Gateway") is set to 192.168.1.1. Under Windows, the easiest way to do this is drop to command prompt (Start > Run > type: cmd) and type: ipconfig You need to find the internal IP address of your existing modem/gateway/router that connects your LAN to the internet. Step 1: Find the IP addresses of your existing gateway/router and clients More detailed step by step instructions on how exactly to convert and use your wireless router as an access point are below: Do not use the Internet/WAN port on the wireless router to be used as an acces point. In essence, the new wireless router/access point needs to be configured to use a LAN IP address in your network range (the same subnet as your other devices), and you need to connect one of its LAN ports to the existing gateway/router. Instead of using your wireless router as intended (NAT routing, DHCP client/server, PPPoE client, etc.), converting it into a wireless access point will save you a lot of headackes and make the configuration much simpler. However, introducing a second NAT router on the network is not a good idea, especially without some tweaking to set it up correctly. Adding an access point to a wired network already in place, or to one where the main NAT router is provided by the ISP is usually the easiest solution. Wireless routers seem more common, and are often priced even lower than wireless access points. If you are unsure, you should consult an expert to help you set up the router again.I've often found it useful to get just the wireless functionality out of a WiFi router and reuse it as an access point. In most cases you can perform a factory reset by pressing a small button on the back of the router for 10-20 seconds.Īfter that the router lights up and needs some minutes to reset all settings.Īfter a factory reset the router loses the connection to all other connected devices and some devices have to be reconnected to the router after such a reset. If nothing helped and you really need access to your AC1200 router, there is also the possibility of a factory reset. Nothing of the methods worked for me and I still not get access to my MediaLink AC1200! You have tried several different IP addresses and still none of them work? Then you should try the IP addresses from the following list. The most common IPs used by MediaLink routers If you have problems logging in to the router or you have forgotten your password. In the list below you can find some of the most commonly used username/password combinations of MediaLink routers. If the credentials do not work, try the following method Enter the username and password, click on the login button and now you should have access to the user interface of the router.Alternatively look into the manual that can be found here: Manual of your router. Sometimes you can find the router login data on the back of the router.Then you will see 2 fields where you can enter the router username and password. ![]() Open your preferred browser and enter 192.168.1.1 in the address bar to access admin panel of your router.Tip: If you have Wi-Fi problems and it is not possible to connect to the router, you can connect your computer and the router with a LAN cable. To access the router login page it is important that you are connected to the router. If you don't have the manual at hand or don't want to search the complete manual for the login credentials, you can use the Quick install guide which you can find below. You can find this information in the Manual of your MediaLink AC1200 router.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |